Welcome to the company ! we have many years of professional experience !
rsdgj@pyzyrsd.com +86 513525609655

sichuan guanghan horizontal sand pump valve

Established in 2001, Puyang Zhong Yuan Restar Petroleum Equipment Co.,Ltd, “RSD” for short, is Henan’s high-tech enterprise with intellectual property advantages and independent legal person qualification. With registered capital of RMB 50 million, the Company has two subsidiaries-Henan Restar Separation Equipment Technology Co., Ltd We are mainly specialized in R&D, production and service of various intelligent separation and control systems in oil&gas drilling,engineering environmental protection and mining industries.We always take the lead in Chinese market shares of drilling fluid shale shaker for many years. Our products have been exported more than 20 countries and always extensively praised by customers. We are Class I network supplier of Sinopec,CNPC and CNOOC and registered supplier of ONGC, OIL India,KOC. High quality and international standard products make us gain many Large-scale drilling fluids recycling systems for Saudi Aramco and Gazprom projects.

Certificate of Honor

CONTACT US

Customer satisfaction is our first goal!

Phone

+86 513525609655

E-Mail

rsdgj@pyzyrsd.com

Address

Road West, North Branch, Jingkai Road, Puyang City

sichuan guanghan horizontal sand pump valve
998777 RL25U Web - Red Lion Pump Products
998777 RL25U Web - Red Lion Pump Products

3. The impeller remains with the motor assembly. Do not remove the impeller. Clean the impeller and the volute passage. Do not use strong solvents on the impeller. 4. Be sure the impeller turns freely after cleaning. 5. Replace the volute plate and base and secure with screws. Risk of severe injury or death by electrical shock, high temperatures, or

PREINSTALLATION CHECKLIST - First Supply
PREINSTALLATION CHECKLIST - First Supply

5. Float switch in “on” position. Pump won’t run. (a) Remove pump. Check for obstruction in pump preventing impeller from rotating. 6. Pump runs, but pumps water intermittently. (a)Pump is air locking. Check flow of water incoming to sump. If discharge pipe. (b)Baffle the incoming stream of water to reduce turbulence.

Pump FAQs - Hydraulic Institute
Pump FAQs - Hydraulic Institute

The multistage ,assembly, of a deep well turbine ,pump, can be seen in Figure 1 (below). Transporting water from deep wells to the surface is the primary application of these pumps. ... A typical centrifugal ,pump impeller, is more easily clogged by solids, ... Two sensor types dominate the market: the conductivity probe and the ,float switch,.

Omnivore 2 HP Grinder Pumps
Omnivore 2 HP Grinder Pumps

Pump shall be properly grounded using its supplied grounding conductor. Do not bypass grounding wires or remove ground prong from attachment plugs. Failure to properly ground the pump system can cause all metal portions of the pump and its surroundings to become energized. Do not handle or unplug the pump with wet hands, when

INSTALLATION INSTRUCTIONS PREINSTALLATION CHECKLIST
INSTALLATION INSTRUCTIONS PREINSTALLATION CHECKLIST

A. Pump will not start or run. Check fuse, low voltage, overload open, open or incorrect wiring, open switch, impeller or seal bound mechanically, defective capacitor or relay when used, motor or wiring shorted. Float assembly held down. Switch defective, damaged, or out of adjustment. B. Motor overheats and trips overload or blows fuse.

INSTALLATION & OPERATION MANUAL - The Pump & Tank …
INSTALLATION & OPERATION MANUAL - The Pump & Tank …

Do not place the ,pump, directly on the ground or sandy or rocky surfaces. ,Sand, and small stones may clog or cause damage to your ,pump,. Make sure the ,float, switches will operate freely without coming in contact with the sides of the sump basin. Contact with the side of the sump basin may cause the ,switch, to malfunction. See figure. 3 9 Ref

Installation Operation and Maintenance ... - Pump Technology
Installation Operation and Maintenance ... - Pump Technology

CONTACTOR UNIT, 3-PHASE, ,FLOAT SWITCH,. EU OVER 400V, US/CDN OVER 250V ,Pump, Contactor BK GY BN BK GY BN BU WH GY YE BK RD BN SUPERVISION RELAY ,Float switch, BU/WH* BN/BK* BN=500-600V SMART RD=380-460V WH GNYE/GN* GC** BU BU Thermal contact Installation 20 8109.282/.583 Salvador ,Installation, Operation, and Maintenance Manual

Discount-Equipment
Discount-Equipment

SUBMERSIBLE ,PUMP, WITH ,FLOAT SWITCH, Revision #3 (12/14/17) Discount-Equipment.com ... ST2037F ,Pump Assembly,..... 22-23 ST2040TF ,Pump Assembly, ... from burrowing itself on soft ,sand, or mud. NEVER operate ,pump, on its side. DO NOT allow the ,pump, to freeze in water.

Installation CVP03 Maintenance PVP03
Installation CVP03 Maintenance PVP03

5) Inlet screen of ,pump, is plugged or the ,impeller, is jammed. Remove the ,pump, screen and clean inlet and ,impeller,. ,PUMP, RUNS AND REMOVES WATER BUT DOES NOT SHUT OFF: 1) ,Float, is stuck in the “ON” position. Check to make sure the ,float, is free to move up and down without obstruction. 2) ,Switch, is defective. Consult factory.

Submersible Sump PumpsInstallation Manual
Submersible Sump PumpsInstallation Manual

241 Wide-Angle ,Float Switch, 243 Wide-Angel ,Float Switch, with Piggyback Plug ... Safety ,Precautions, ... Do not lift or carry a ,pump, or a ,float assembly, by its power cord. This will damage the power cord, and could expose the electrically live wires inside the power cord.

Chat Online Inquiry Email

Business cooperation

+86 513525609655

Company address

Road West, North Branch, Jingkai Road, Puyang City