Welcome to the company ! we have many years of professional experience !
rsdgj@pyzyrsd.com +86 513525609655

3pnj sand pump

Established in 2001, Puyang Zhong Yuan Restar Petroleum Equipment Co.,Ltd, “RSD” for short, is Henan’s high-tech enterprise with intellectual property advantages and independent legal person qualification. With registered capital of RMB 50 million, the Company has two subsidiaries-Henan Restar Separation Equipment Technology Co., Ltd We are mainly specialized in R&D, production and service of various intelligent separation and control systems in oil&gas drilling,engineering environmental protection and mining industries.We always take the lead in Chinese market shares of drilling fluid shale shaker for many years. Our products have been exported more than 20 countries and always extensively praised by customers. We are Class I network supplier of Sinopec,CNPC and CNOOC and registered supplier of ONGC, OIL India,KOC. High quality and international standard products make us gain many Large-scale drilling fluids recycling systems for Saudi Aramco and Gazprom projects.

Certificate of Honor

CONTACT US

Customer satisfaction is our first goal!

Phone

+86 513525609655

E-Mail

rsdgj@pyzyrsd.com

Address

Road West, North Branch, Jingkai Road, Puyang City

3pnj sand pump
Discount-Equipment
Discount-Equipment

SUBMERSIBLE ,PUMP, WITH ,FLOAT SWITCH, Revision #3 (12/14/17) Discount-Equipment.com ... ST2037F ,Pump Assembly,..... 22-23 ST2040TF ,Pump Assembly, ... from burrowing itself on soft ,sand, or mud. NEVER operate ,pump, on its side. DO NOT allow the ,pump, to freeze in water.

Installation Operation and Maintenance ... - Pump Technology
Installation Operation and Maintenance ... - Pump Technology

CONTACTOR UNIT, 3-PHASE, ,FLOAT SWITCH,. EU OVER 400V, US/CDN OVER 250V ,Pump, Contactor BK GY BN BK GY BN BU WH GY YE BK RD BN SUPERVISION RELAY ,Float switch, BU/WH* BN/BK* BN=500-600V SMART RD=380-460V WH GNYE/GN* GC** BU BU Thermal contact Installation 20 8109.282/.583 Salvador ,Installation, Operation, and Maintenance Manual

Pump FAQs - Hydraulic Institute
Pump FAQs - Hydraulic Institute

The multistage ,assembly, of a deep well turbine ,pump, can be seen in Figure 1 (below). Transporting water from deep wells to the surface is the primary application of these pumps. ... A typical centrifugal ,pump impeller, is more easily clogged by solids, ... Two sensor types dominate the market: the conductivity probe and the ,float switch,.

REGAL 42SC OWNER'S MANUAL Pdf Download | ManualsLib
REGAL 42SC OWNER'S MANUAL Pdf Download | ManualsLib

Page 277: Bilge ,Pump,/,Float Switch, Chapter 8 TYPICAL BILGE ,PUMP,/,FLOAT SWITCH, Grates ,Float, Bilge ,Switch Pump, Your vessel offers as standard equipment bilge ,pump, ser- vice. Periodically check the grates for debris and test spray the units down with water. Make sure that a steady stream of water exits the through hull fi...

Installation CVP03 Maintenance PVP03
Installation CVP03 Maintenance PVP03

5) Inlet screen of ,pump, is plugged or the ,impeller, is jammed. Remove the ,pump, screen and clean inlet and ,impeller,. ,PUMP, RUNS AND REMOVES WATER BUT DOES NOT SHUT OFF: 1) ,Float, is stuck in the “ON” position. Check to make sure the ,float, is free to move up and down without obstruction. 2) ,Switch, is defective. Consult factory.

INSTALLATION and OPERATION MANUAL Submersible Sewage ...
INSTALLATION and OPERATION MANUAL Submersible Sewage ...

Float, movement restricted. 2b. Disconnect level control. Set ohmmeterprotector). CAUTION! ,Pump, may start 2b. ,Switch, will not activate ,pump, or is defec- for a low range, such as 100 ohms full scaleunexpectedly. Disconnect power supply. tive. and connect to level control leads. ActuatePump operates noisily or vibrates 4.

Simer Pumps 3989 User Manual
Simer Pumps 3989 User Manual

View and Download Simer Pumps 3989 instruction manual online.

ST-2037 Rev 1
ST-2037 Rev 1

ALWAYS place the ,pump, in an upright position on a platform before using. The platform will prevent the ,pump, from burrowing itself on soft ,sand, or mud. NEVER operate ,pump, on its side. DO NOT allow the ,pump, to freeze in water. NEVER leave an open ,pump, chamber unattended. The electrical voltage required to operate the ,pump, can

Submersible Sump PumpsInstallation Manual
Submersible Sump PumpsInstallation Manual

241 Wide-Angle ,Float Switch, 243 Wide-Angel ,Float Switch, with Piggyback Plug ... Safety ,Precautions, ... Do not lift or carry a ,pump, or a ,float assembly, by its power cord. This will damage the power cord, and could expose the electrically live wires inside the power cord.

INSTALLATION & OPERATION MANUAL - The Pump & Tank …
INSTALLATION & OPERATION MANUAL - The Pump & Tank …

Do not place the ,pump, directly on the ground or sandy or rocky surfaces. ,Sand, and small stones may clog or cause damage to your ,pump,. Make sure the ,float, switches will operate freely without coming in contact with the sides of the sump basin. Contact with the side of the sump basin may cause the ,switch, to malfunction. See figure. 3 9 Ref

Chat Online Inquiry Email

Business cooperation

+86 513525609655

Company address

Road West, North Branch, Jingkai Road, Puyang City